View this release
Alternative links
========================================================================================================================================================================================================
Black Lotus Coalition
Presents:
FMDA 19X.2 stipple pack
By : TooAceForThisShit
A Special thank you to:
Moderator Gage
kingoftwins22
letfreedomringllc
KYGS666 of AWCY?
The entire Black Lotus Coalition family
========================================================================================================================================================================================================
Print settings:
PLA+, PLAPRO, or stronger. Most frames tested were tested with ovrature (PLA PRO).
.2 layer hight or lower the rose stipple specifically, as a smaller layer hight
. The 4 nozzle is the largest that has been tested and proven to work; smaller nozzles will provide finer details but have not been tested for strength, so proceed with caution.
100% Infill
Supports on trees or organic supports are fine.
=======================================================================================================================================================================================================
Parts list:
Complete parts kits can be found at https://jsdsupply.com/?aff=18 (this is an affilate link that dirrectly supports Black Lotus Coalition)
You will need a complete Glock 19 Gen 3 slide.
FMDA19.2 Rails
A Glock 19 "three pin" locking block your lower parts kit will most likely not come with one. also make shure it is a glock 19 locking block as it is not compatable with glock 17 or 26 locking blocks.
A complete gen 3 glock 19 lower parts kit your lower parts kit should include
A Trigger Housing
A Trigger with Bar
A Trigger Spring
A Trigger Connector
A Slide Lock
A Slide Lock Spring
A Magazine Catch
A Magazine Catch Spring
A Slide Stop Lever
A Trigger Housing Pin
A Trigger Pin
A Locking block Pin
A Glock 17 Length Magazine
=========================================================================================================================================================================================================
Tools:
For assembly, you will need
A 3mm drill bit
A 4mm drill bit
A 3mm or 1/8-inch punch
A mallot or hammer I like a mallot as it can assist with the installation of the rear rails.
A small flathead screwdriver
Tools to remove your supports
========================================================================================================================================================================================================
For assembly:
https://odysee.com/@Ivan%27s_CAD_Streams:c/FMDADD17.2GlockFrameTutorial:e?r=6jT5tpFBc8edPDXzPH6yUPRsqygx4Lfq
^ assembly should be the exact same as this video just with sligtly different parts
assembly is the same as any other printed glock 19
Black Lotus Coalition
Presents:
FMDA 19X.2 stipple pack
By : TooAceForThisShit
A Special thank you to:
Moderator Gage
kingoftwins22
letfreedomringllc
KYGS666 of AWCY?
The entire Black Lotus Coalition family
========================================================================================================================================================================================================
Print settings:
PLA+, PLAPRO, or stronger. Most frames tested were tested with ovrature (PLA PRO).
.2 layer hight or lower the rose stipple specifically, as a smaller layer hight
. The 4 nozzle is the largest that has been tested and proven to work; smaller nozzles will provide finer details but have not been tested for strength, so proceed with caution.
100% Infill
Supports on trees or organic supports are fine.
=======================================================================================================================================================================================================
Parts list:
Complete parts kits can be found at https://jsdsupply.com/?aff=18 (this is an affilate link that dirrectly supports Black Lotus Coalition)
You will need a complete Glock 19 Gen 3 slide.
FMDA19.2 Rails
A Glock 19 "three pin" locking block your lower parts kit will most likely not come with one. also make shure it is a glock 19 locking block as it is not compatable with glock 17 or 26 locking blocks.
A complete gen 3 glock 19 lower parts kit your lower parts kit should include
A Trigger Housing
A Trigger with Bar
A Trigger Spring
A Trigger Connector
A Slide Lock
A Slide Lock Spring
A Magazine Catch
A Magazine Catch Spring
A Slide Stop Lever
A Trigger Housing Pin
A Trigger Pin
A Locking block Pin
A Glock 17 Length Magazine
=========================================================================================================================================================================================================
Tools:
For assembly, you will need
A 3mm drill bit
A 4mm drill bit
A 3mm or 1/8-inch punch
A mallot or hammer I like a mallot as it can assist with the installation of the rear rails.
A small flathead screwdriver
Tools to remove your supports
========================================================================================================================================================================================================
For assembly:
https://odysee.com/@Ivan%27s_CAD_Streams:c/FMDADD17.2GlockFrameTutorial:e?r=6jT5tpFBc8edPDXzPH6yUPRsqygx4Lfq
^ assembly should be the exact same as this video just with sligtly different parts
assembly is the same as any other printed glock 19