
View this release
Alternative links
This is a custom-made Clipping jig for a Chinese solvent trap, Made by Caska with Love.
Please be sure your solvent trap is equal to these specs to make sure this jig will work for you.
Overall Length: 9"
Tube length: 8.25”
Outside Diameter: 1.6"
Internal Diameter: 1.38"
Weight: 29 oz
Example of Kit: https://kmwhisper.com/collections/solvent-traps/products/form-1-kit (This can be found direct from china for far less)
What you need:
2x 6x17x6 mm Bearings : https://www.amazon.com/uxcell-606-2RS-Bearing-6x17x6 mm-Bearings/dp/B07MX9V7VB/
1x 6.00 mm (15/64th) HSS Drill bit : https://www.amazon.com/DEWALT-DW1915-64-Inch-Ferrous-Oxide/dp/B00004YMEN/
1x Clamp or 2x M3x50 mm Screws and M3 Nuts
Printing:
Print in PLA or Better
100% Infill
If you need Supports, Supports where NOT touching the build plate
Print with Words on Build Plate
Instructions:
Press fit bearings into top (where the words are) and bottom slots. Use Glue if needed.
Insert K-Cup with the top (Not the cone) twords the top (words) of the jig and press it in.
Use a C-Clamp OR M3x50 mm Bolts and Nuts to tighten the jig around the K-Cup.
Use DrillPress to slowly drill hole.
Unclasp/Unbolt to release the K-Cup (might need to push out)
Notes:
Do not go fast as it can break bits and might make the jig warp/melt.
You will need to cut/break the printed back wall (notch where on the bolt holes side) so the bottom of the jig can squeeze around the cups.
LBRY Tags: 3d printed; fosscad; guncad; jig; solvent trap
Please be sure your solvent trap is equal to these specs to make sure this jig will work for you.
Overall Length: 9"
Tube length: 8.25”
Outside Diameter: 1.6"
Internal Diameter: 1.38"
Weight: 29 oz
Example of Kit: https://kmwhisper.com/collections/solvent-traps/products/form-1-kit (This can be found direct from china for far less)
What you need:
2x 6x17x6 mm Bearings : https://www.amazon.com/uxcell-606-2RS-Bearing-6x17x6 mm-Bearings/dp/B07MX9V7VB/
1x 6.00 mm (15/64th) HSS Drill bit : https://www.amazon.com/DEWALT-DW1915-64-Inch-Ferrous-Oxide/dp/B00004YMEN/
1x Clamp or 2x M3x50 mm Screws and M3 Nuts
Printing:
Print in PLA or Better
100% Infill
If you need Supports, Supports where NOT touching the build plate
Print with Words on Build Plate
Instructions:
Press fit bearings into top (where the words are) and bottom slots. Use Glue if needed.
Insert K-Cup with the top (Not the cone) twords the top (words) of the jig and press it in.
Use a C-Clamp OR M3x50 mm Bolts and Nuts to tighten the jig around the K-Cup.
Use DrillPress to slowly drill hole.
Unclasp/Unbolt to release the K-Cup (might need to push out)
Notes:
Do not go fast as it can break bits and might make the jig warp/melt.
You will need to cut/break the printed back wall (notch where on the bolt holes side) so the bottom of the jig can squeeze around the cups.
LBRY Tags: 3d printed; fosscad; guncad; jig; solvent trap