496
6
M&P M2.0 Personal Use Only
This STL models the geometry/fit for the Smith & Wesson M&P M2.0of any caliber. Intended for hobbyist, personal use and hands-on fitment .
Print notes
Print at 0.15 mm layer height.
Supports required (small overhang + striker-channel cutout).
Material: Carbon-fiber nylon or other heat/impact-resistant filament recommended. PLA+ ok for mockups but will not hold up to heavy/extended use.
Orient part so load-bearing faces have max wall count and shells.
Compatibility
Sized for Smith & Wesson M&P M2.0
Personal use only.
Legal & safety
By downloading you agree this is for hobbyist paint-marker use only. Laws vary — you are responsible for compliance. Author not liable for misuse, modification, damage, or injury.
This product renders the striker safety plunger non-functional, use at your own risk.
Safety first (do this before working)
Remove magazine/load. Verify chamber is empty. Work on a clean, well-lit bench with parts tray.
Prep (what to check & why)
Inspect the trigger-bar edge that contacts the striker/channel. If there are burrs or sharp edges, smooth them until rounded — do not shorten or change geometry; only remove burrs so mating faces are smooth to the touch.
Re-check fit to ensure you did not alter protrusion or travel.
Spring & cycling note
Some builds benefit from a heavier return/recoil spring for more stable cycling under heavier use(10mm/45cal needs 22-25lb spring) — consult a technician if you need help.
Install
Reassemble slide/upper so the slide can be racked normally. Rack and lock open to access the backplate/striker channel.
Depress the visible portion of the striker-channel/retainer (use the grip tool or a small punch) just enough to relieve tension so the backplate can be eased off — push, don’t pry.
Seat the device, keeping the striker channel depressed, then slide the backplate back on until it clicks/engages. If it won’t slide on cleanly, do very minimal filing of the channel liner tip to help feed — check fit frequently.
Apply a light coating of marker-appropriate oil/grease to moving surfaces and reassemble.
Function check & troubleshooting
With marker unloaded, cycle the slide by hand and confirm smooth, repeatable seating. If spongy or binding, stop and inspect — minor high spots can be smoothed; if unsure, consult a technician.
After a successful manual check, test-fire in a safe, controlled environment with appropriate protective gear and short strings to confirm reliability.
WORKS IN: M&P 2.0
(9mm/10mm/40cal/45cal) (Full/Compact/Subcompact/Metal/Performance/Thumb Safety)
WILL NOT WORK IN M&P® 1.0, SHIELD, SD, OR BODYGUARD MODELS
WILL NOT WORK WITH THE APEX FORWARD SET SEAR ACTUATOR
LBRY Tags: disable-support; c:disable-reactions-comments; c:disable-slimes-comments; c:disable-slimes-video; smith an wesson; frt; pistol; 9mm; gun
This STL models the geometry/fit for the Smith & Wesson M&P M2.0of any caliber. Intended for hobbyist, personal use and hands-on fitment .
Print notes
Print at 0.15 mm layer height.
Supports required (small overhang + striker-channel cutout).
Material: Carbon-fiber nylon or other heat/impact-resistant filament recommended. PLA+ ok for mockups but will not hold up to heavy/extended use.
Orient part so load-bearing faces have max wall count and shells.
Compatibility
Sized for Smith & Wesson M&P M2.0
Personal use only.
Legal & safety
By downloading you agree this is for hobbyist paint-marker use only. Laws vary — you are responsible for compliance. Author not liable for misuse, modification, damage, or injury.
This product renders the striker safety plunger non-functional, use at your own risk.
Safety first (do this before working)
Remove magazine/load. Verify chamber is empty. Work on a clean, well-lit bench with parts tray.
Prep (what to check & why)
Inspect the trigger-bar edge that contacts the striker/channel. If there are burrs or sharp edges, smooth them until rounded — do not shorten or change geometry; only remove burrs so mating faces are smooth to the touch.
Re-check fit to ensure you did not alter protrusion or travel.
Spring & cycling note
Some builds benefit from a heavier return/recoil spring for more stable cycling under heavier use(10mm/45cal needs 22-25lb spring) — consult a technician if you need help.
Install
Reassemble slide/upper so the slide can be racked normally. Rack and lock open to access the backplate/striker channel.
Depress the visible portion of the striker-channel/retainer (use the grip tool or a small punch) just enough to relieve tension so the backplate can be eased off — push, don’t pry.
Seat the device, keeping the striker channel depressed, then slide the backplate back on until it clicks/engages. If it won’t slide on cleanly, do very minimal filing of the channel liner tip to help feed — check fit frequently.
Apply a light coating of marker-appropriate oil/grease to moving surfaces and reassemble.
Function check & troubleshooting
With marker unloaded, cycle the slide by hand and confirm smooth, repeatable seating. If spongy or binding, stop and inspect — minor high spots can be smoothed; if unsure, consult a technician.
After a successful manual check, test-fire in a safe, controlled environment with appropriate protective gear and short strings to confirm reliability.
WORKS IN: M&P 2.0
(9mm/10mm/40cal/45cal) (Full/Compact/Subcompact/Metal/Performance/Thumb Safety)
WILL NOT WORK IN M&P® 1.0, SHIELD, SD, OR BODYGUARD MODELS
WILL NOT WORK WITH THE APEX FORWARD SET SEAR ACTUATOR
LBRY Tags: disable-support; c:disable-reactions-comments; c:disable-slimes-comments; c:disable-slimes-video; smith an wesson; frt; pistol; 9mm; gun
Related to This Release
849
8
Smith & Wesson M&P 15-22 Print Package
I have found a printable lower receiver and magazine that can be printed for the Smith & Wesson M&P 15-22, I did not make any of the things included,…
483
8
step file mac 11 cnc barrel ready to ecm 8mm id
STEP FİLE 8mm inner diameter cnc mac 11 barrel ready to ecm rifling
215
4
Krrawn Shroud Mac n Cheese Remix for Parts Dispensed Mac Upper
This remix is for the Parts Dispensed M11 upper receiver to fit the slightly longer trunnion.
LBRY Tags: fosscad; 3d2a; mac n cheese; guncad; krrawn
174
7
S&W M&P 2.0 Compact High Resolution 3d Scan
High Resolution Scan of M&P 2.0 Compact
115
3
3D Printed M&P Shield 45 Magazine Carrier - File Release
This is the full file package with Readme, STEP, STL, and Native models for an OWB 3D Printed M&P Shield 45 Magazine Carrier.
LBRY Tags: 3d printing…
Twitter
Matrix
Source
