918
11
View this release
Alternative links
Had a problem with the SCS Kabuto cam dropping too low causing the bolt to get stuck in Semi mode. When the bolt was stuck the hammer could still drop potentially causing OOB detonation. This housing adds a small shelf to prevent the cam from turning too much.
There is three versions one with a printed shelf, one with M3 hardware to adjust to your setup, and one with a spring which should work with any setup you drop the housing into. Use some kind of adhesive if your spring fits loosely.
Use high number of walls or 100% infill. Smaller layer heights will print better holes. No supports necessary. Print in PLA+ or PLA Pro.
Update 4: New version for people that are having trouble finding a 4.5mm pen spring. Uses these springs https://www.amazon.com/dp/B076M55S7F, if they are out of stock, the specs are Outer Diameter: 4mm/0.16 Wire Diameter: 0.4mm/0.01 Total Length: 10mm/0.39
Update 3: Added a version that uses a 4.5mm pen spring. I cut mine down to 10mm long but you can cut to the length you need. Press fit into the hole, clean up the opening if needed depending on your bed texture. Depending on your print accuracy you might need some glue to hold the spring in if it falls out easily.
Update 2: There was a problem with the screw hitting a lip on some upper receivers. I added a model that angles the screw 15 degrees to clear it. Use this model if you have problems closing the upper or if it's hard to turn the safety to the FRT position.
Update 1: Added a second model that uses M3 hardware for adjustability. Use an M3 nut and M3x8 or M3x12 depending on the length you need. Add some threadlocker to the screw.
Original design by @Kabuto-Filearms
My changes are built on the SCS compatible housing by @Fl-Eggs:8
LBRY Tags: guncad; kabuto; frt; scs; t.u.r.d
There is three versions one with a printed shelf, one with M3 hardware to adjust to your setup, and one with a spring which should work with any setup you drop the housing into. Use some kind of adhesive if your spring fits loosely.
Use high number of walls or 100% infill. Smaller layer heights will print better holes. No supports necessary. Print in PLA+ or PLA Pro.
Update 4: New version for people that are having trouble finding a 4.5mm pen spring. Uses these springs https://www.amazon.com/dp/B076M55S7F, if they are out of stock, the specs are Outer Diameter: 4mm/0.16 Wire Diameter: 0.4mm/0.01 Total Length: 10mm/0.39
Update 3: Added a version that uses a 4.5mm pen spring. I cut mine down to 10mm long but you can cut to the length you need. Press fit into the hole, clean up the opening if needed depending on your bed texture. Depending on your print accuracy you might need some glue to hold the spring in if it falls out easily.
Update 2: There was a problem with the screw hitting a lip on some upper receivers. I added a model that angles the screw 15 degrees to clear it. Use this model if you have problems closing the upper or if it's hard to turn the safety to the FRT position.
Update 1: Added a second model that uses M3 hardware for adjustability. Use an M3 nut and M3x8 or M3x12 depending on the length you need. Add some threadlocker to the screw.
Original design by @Kabuto-Filearms
My changes are built on the SCS compatible housing by @Fl-Eggs:8
LBRY Tags: guncad; kabuto; frt; scs; t.u.r.d
Related to This Release
508
9
SAINT KABUTO T.U.R.D Housing
Kabuto safety housing for Springfield Saint lowers. Looser fit version works better with fiber reinforced filaments. Includes extended pin.
LBRY Tag…
309
3
20250724 SCS Kabuto Housing Sqweeeeeeee
20250727_Rev1 - Reported range test of ~200 rounds, but user noted that housing was broken above pin hole when checked afterwards. Slightly adjusted …
1297
18
SS AKV (open beta)
SSAKV remix of SSAK by Si3gu2
LBRY Tags: akv; super safety; brrrrr; ssakv; 3d2a
457
15
SSAK Captured Recoil Buffer
This is a remix of KP's AK Recoil Buffer that includes 3 different size buffers (12MM, 15MM, 18MM) along with retainers to hold the buffer captive to…
117
9
0pF0rArm0ry_RR_Optic_Riser
I finally made something useful. Feel free to improve on this design. Credit to Invizi and RiceCutta for the OG files I based this off of.
LBRY Tags…
Twitter
Matrix
Source
