451
7
View this release
Alternative links
printed ar magazine (treat this as a beta test), personal prints made on a P1S
Update 1: Updated follower to V2, removed V1, and re-uploaded files.
Update 2: *Tested fitment of PPA-CF mag body. V2 follower is tight and will need to be broken in. Once broken in, mag runs fine.* see known issues 2
Update 3: Added 350 legend design (non tested). Updated follower stop 2mm lower, possible fix to feed lip breaking.
Update 4: -Shortened "Follower" by 2mm. This will allow full mags to be easily inserted.
-Loosen tolerances on "Follower" leads to smoother mag, and will not have to be broken in.
- The follower stop on "mag body" has been decreased by .5mm to keep the follower from hitting the feed lips. Follower may still hit the feed lips. it is a fine balance between last round bolt hold reliability and protecting feed lips.
- Removed material from the back rib from the top of "mag body". Noticed wear on the test article, not sure if this will affect strength. I will add material back if this is an issue.
-Known Issue 2, hopefully fixed with this update.
Troubleshooting: Print MAG BODY with 20° tilt forward. You will only need support on the bottom. Light sanding on the bottom recomended. Always print followers in PLA or PLA pro
Known issues: 1: Possible tolerance issues between AR brands. Mag should be close to 63.45x22.5mm for the mag well. Might decrease to 63.2x22.25mm to fit more platforms. Once more data is acquired, V2 MAG BODY will be released and a note will be added to the update section and this note will be removed.
2: *PPA-CF feed lip broke while loading and unloading test. This could be because follower catch is not in tolerance, allowing additional stress on the right feed lip. PLA pro is still holding up. POSSIBLE FIXES: might increase the thickness of the feed lips by .25mm. Will experiment with different print orientations. The current is very horizontal, if needed, I will make a model with modeled in support. If so, I will have 2 models with and without support.*
LBRY Tags: magazine; ar; printed; 5.56; 556
Update 1: Updated follower to V2, removed V1, and re-uploaded files.
Update 2: *Tested fitment of PPA-CF mag body. V2 follower is tight and will need to be broken in. Once broken in, mag runs fine.* see known issues 2
Update 3: Added 350 legend design (non tested). Updated follower stop 2mm lower, possible fix to feed lip breaking.
Update 4: -Shortened "Follower" by 2mm. This will allow full mags to be easily inserted.
-Loosen tolerances on "Follower" leads to smoother mag, and will not have to be broken in.
- The follower stop on "mag body" has been decreased by .5mm to keep the follower from hitting the feed lips. Follower may still hit the feed lips. it is a fine balance between last round bolt hold reliability and protecting feed lips.
- Removed material from the back rib from the top of "mag body". Noticed wear on the test article, not sure if this will affect strength. I will add material back if this is an issue.
-Known Issue 2, hopefully fixed with this update.
Troubleshooting: Print MAG BODY with 20° tilt forward. You will only need support on the bottom. Light sanding on the bottom recomended. Always print followers in PLA or PLA pro
Known issues: 1: Possible tolerance issues between AR brands. Mag should be close to 63.45x22.5mm for the mag well. Might decrease to 63.2x22.25mm to fit more platforms. Once more data is acquired, V2 MAG BODY will be released and a note will be added to the update section and this note will be removed.
2: *PPA-CF feed lip broke while loading and unloading test. This could be because follower catch is not in tolerance, allowing additional stress on the right feed lip. PLA pro is still holding up. POSSIBLE FIXES: might increase the thickness of the feed lips by .25mm. Will experiment with different print orientations. The current is very horizontal, if needed, I will make a model with modeled in support. If so, I will have 2 models with and without support.*
LBRY Tags: magazine; ar; printed; 5.56; 556
Related to This Release
579
9
Hello Kitty SG22
No description provided for this release
LBRY Tags: art; 3d printing; sg22
770
49
1
Unseenkiller - Hydra Ish Riser
No Odysee comments will be monitored.
Please read the readme for information inside of each ZIP.
Feel free to reach out to me @ unseenkiller on Inst…
139
5
C8A2 Reference Model
Unknown developer, File available in STEP, IGES, and X_T file format
The Colt Canada C8 carbine range are carbine variants of the C7 family, and are…
2251
51
AR15 Magazine Spring Machine
This tool will allow you to quickly make correctly sized springs for AR-15 magazines and is
adjustable to allow for various types of wire. This proje…
866
20
Buffer tower plug and cap
This is a picatinny rail adapter for a standard ar-15 buffer tower. It is 2 pieces with printed threads for eliminating the buffer tube and replacin…
Twitter
Matrix
Source
