View this release
Alternative links
Sling Kontrol V1.1 "by" Qwerm
A shameless ripoff of Subrev's Sling Control, a picatinny accessory that helps store your sling when not using your rifle.
Changelog:
-v1.1
Added looser fitting versions of the snap on version in order to make it easier to attach. I suggest SlingKontrol-Part1-Snap-Loose for a good balance between ease of installation and proper fit.
Print orientation: Print everything on it's side.
Settings used:
Material: PLA+
Extruder Temp: 210c
Bed Temp: 60c
Layer Height: 0.2mm
Wall Line Count: 4
Infill Percentage: 100%
Support: None
Fuzzy Skin: On
Fuzzy Skin Outside Only: On
Fuzzy Skin Thickness: 0.1mm
Fuzzy Skin Density: 10.0/mm
Materials Needed (Dont ask me why I mix metric and imperial parts):
1/8 Inch Shock Cord
2x M3x8 Screws
1x 3/16 Dia. 1/4" Long Set Screw
Directions:
- Cut a length of shock cord and feed it through the larger part.
- Insert both ends into the smaller part
- Screw in both M3 screws until snug enough to keep the ends of the shock cord from pulling out but not enough for you to strip out the holes.
Set Screw Version - Slide the large part onto your rifle, aligning the hole with a slot in your picatinny rail and screw in the set screw until the mount no longer moves up and down the picatinny rail.
Snap Fit Version - Snap the large part onto your rifle, aligning the tab with a slot in your picatinny rail.
Credit to SubverTech for the design. For more info check out their website:
https://subrevtech.com/product/sling-control/
https://subrevtech.com/instructions/
LBRY Tags: 3d printed; 3dpg; sling
A shameless ripoff of Subrev's Sling Control, a picatinny accessory that helps store your sling when not using your rifle.
Changelog:
-v1.1
Added looser fitting versions of the snap on version in order to make it easier to attach. I suggest SlingKontrol-Part1-Snap-Loose for a good balance between ease of installation and proper fit.
Print orientation: Print everything on it's side.
Settings used:
Material: PLA+
Extruder Temp: 210c
Bed Temp: 60c
Layer Height: 0.2mm
Wall Line Count: 4
Infill Percentage: 100%
Support: None
Fuzzy Skin: On
Fuzzy Skin Outside Only: On
Fuzzy Skin Thickness: 0.1mm
Fuzzy Skin Density: 10.0/mm
Materials Needed (Dont ask me why I mix metric and imperial parts):
1/8 Inch Shock Cord
2x M3x8 Screws
1x 3/16 Dia. 1/4" Long Set Screw
Directions:
- Cut a length of shock cord and feed it through the larger part.
- Insert both ends into the smaller part
- Screw in both M3 screws until snug enough to keep the ends of the shock cord from pulling out but not enough for you to strip out the holes.
Set Screw Version - Slide the large part onto your rifle, aligning the hole with a slot in your picatinny rail and screw in the set screw until the mount no longer moves up and down the picatinny rail.
Snap Fit Version - Snap the large part onto your rifle, aligning the tab with a slot in your picatinny rail.
Credit to SubverTech for the design. For more info check out their website:
https://subrevtech.com/product/sling-control/
https://subrevtech.com/instructions/
LBRY Tags: 3d printed; 3dpg; sling